How to Measure a Chainsaw Chain 2021

  • May 4, 2021
  • / By MF

If you want to measure your chainsaw chain, you must know the pitch. The most accurate way of calculating the pitch is to measure the distance between three rivets on your chainsaw chain. The measurement must begin from the center of the first rivet and end at the center of the third.

Then divide that distance into two equal parts and that number will be the pitch of your chainsaw chain. After that, grab hold of a vernier caliper and determine the width of a single tooth of the chain. That’s it, you’re pretty much done because now you only need to count the number of teeth in the chain to complete the measurement process.

To start with, make sure you mark the blade you’ll sharpen first so that you don’t repeat the process twice. In this way, you can ensure that each blade has the same amount of sharpness. Next, look for the right file that will go with your chainsaw.

Best Chainsaw Chain for Hardwood

Be careful while aligning the blade of the file with that of the chainsaw. The angle between the chainsaw blade and the file should be approximately 25 degrees but it depends on the chainsaw you own. Then lightly brush the file against the tooth of the chainsaw in a forward and backward motion. 

Repeat this process four to five times with a little pressure to ensure the success of the sharpening process and then move on to the next tooth.

How To Put A Chain On A Chainsaw?

First of all, you need to be certain that the chain is facing the right way. The head of each of the teeth of the chainsaw blade should face forwards to ensure a successful attempt. Place the chain on the chain bar and check the position of the tension adjuster on the bar.

After that, cover the chain bar and fix the nuts on the cover to keep it in place. However, you shouldn’t screw them too tightly since that will hamper the process of adjusting the chain. Change the tension of the chainsaw blade until the chain becomes tight enough by using a screwdriver to twist the tension adjuster.

Finally, check the chain to ensure free movement and then tighten the bolts on the chain bar to wrap up the job.

How Tight Should A Chainsaw Chain Be?

Tightening the chain on your chainsaw can be quite tricky. You need to carry out the process with utmost precision because it can neither be too tight nor can it be too loose. Both of these faults will cause problems when you attempt to use your chainsaw.

The chain should be tight enough to not be visibly separate from the bar. In that case, it will not work properly and may even damage the material it’s working on. On the other hand, tightening the chain beyond its limit will make the chainsaw break so you must be careful.

If you’re not sure about the tension in your chain, pull it away and observe the drive links. If they remain engaged then you’re good to go.

How To Untangle A Chainsaw Chain?

If you find your chainsaw saw in a state of mess, then you can easily untangle it following a series of simple steps. At first, you should place it on a plain surface and try to create the shape of a circle using the chain by roughly tidying it up.

You’ll see that most of the chain will be easy to untangle. However, some loops may make the job a little difficult. You’ll have to make sure all the loops are on the same side of the chain. Then gently hold the chain and move it over the loops so that they untangle. After that, you’ll be left with a perfectly tidy chainsaw chain.

What Is The Best Chainsaw Chain?

There is a great debate on which chainsaw chain is the best one. Since the standards for being the best varies from person to person, you may hear a different name every time you ask someone this question. However, according to me, the Trilink S62 is the best chainsaw chain you’ll get your hands on.

It’s an 18-inch chain that is more than enough for any job you use it for. On top of that, its versatility makes it compatible with a range of chainsaw models. It is immensely useful and contains rust-resistant properties which make it durable and worth every penny.

How To Shorten A Chainsaw Chain?

If your chainsaw chain comes with a master link, the first and foremost step would be to remove it. But at first, you’ll have to identify it since it’s not just any other link. The manufacturers will make this quite easy for you by making the appearance of the master link distinct.

Usually, you can use pliers or any kind of similar tool to complete this procedure. Removing the master link will allow you to remove the number of links in the chain that you desire and shorten it. After that, all you have to do is connect the chain with itself again and make sure the tension is moderate.

How To Measure Chainsaw Chain Length?

You can use your chainsaw bar to determine the length of the chain it needs. The procedure of taking this measurement is incredibly easy if you do it right. Use a measuring tool such as a tape measure to obtain the distance between the tip of the bar up to the point where it comes out of the casing.

After that, all you have to do is simply convert that number to the even number it is the closest to. You’re pretty much done because all you have to do now is to find a chain with the same length that you obtained from the bar.

How To Replace A Chainsaw Chain?

The first thing that you have to do is remove the old chain from the chainsaw bar. Adjust the tensioning screw such that the tension in the bar is low. As a result, it’ll be easier for you to replace the chain. Position the new chain on the bar such that the drive links are aligned on the sprockets.

Try to tighten the chain by pulling the bar away from the machine. After that, replace the side plate that you had disintegrated before removing the old chain. Adjust the tightness of the new chain by twist the tension screw back and forth until you reach the ideal tension.

What Do The Numbers On A Chainsaw Chain Mean?

I’ve already talked about measuring the pitch of a chainsaw chain above. You’ll have to carry out that process only if the pitch is not mentioned in the chain itself. Most manufacturers tend to make the job easier for users and state the pitch on the chain.

Along with that, the numbers also include information about the gauge and the number of drive links present in the chain. In those cases, you won’t have to work hard to find out whether the chain you’re looking at is compatible with your chainsaw or not. Taking a careful look at the numbers in the chain will help you decide whether the chain will be useful to you or not.

How To Sharpen A Chainsaw Chain With An Electric Sharpener?

Using an electric sharpener on your chainsaw blade requires a sufficient amount of knowledge about the gauge, pitch, and drive links of the chain. If you're sure about those pieces of information, it’s time for you to start setting up the sharpening stone of the electric sharpener you’re going to use.

The next step is to place the blade of the sharpener at an angle that boosts the efficiency of the sharpening process. This is usually up to 80 degrees. After that, you’ll need to open the instruction manual of your chain and look for the tooth angle.

Finally, sharpen each tooth using the machine and move on to the next one only when you notice luminosity in the previous one.

How To Replace Chain Tensioner On Stihl Chainsaw?

At first, you need to unscrew the plate of the tensioner on the chainsaw using compatible screwdrivers. There may also be clips instead of the screws and you’ll have to use different tools in those cases. Next, remove the plate and use another screwdriver to take off the screw for the tension adjuster.

After that, use the sharp end of the driver to carefully take out the adjuster. You’ll see that the adjuster will come out in one piece if it’s not broken. All you have to do now is position the new tension adjuster in the same place and screw it tightly like the one you just took out. Put the plate back in place and work on the screws on it as well.

How To Tighten The Chain On A Remington Electric Chainsaw?

To start with, you should loosen the nuts on the bar of the chainsaw but make sure that they’re not removed completely. After that, twist the tension adjusting screw in a clockwise direction while holding the chainsaw bar up. Adjust until you reach the ideal tension.

You should be able to check the tension by slightly pulling the chain off the chainsaw. It should fit perfectly, neither too tight nor too loose. For Remington electric chainsaws, the drive links often stay one-sixteenth of an inch below the bar. You should be able to move the chain on the bar with your hand.

Final Verdict

Maintaining a chainsaw can be quite difficult and that’s exactly what inspired the creation of this article. The questions addressed in this piece of writing are ones that confused people most frequently. I’ve tried to keep the contents of this article as diverse as possible and answer the most important questions about chainsaws.

I hope that this article about sharpening, tightening, and replacing a chainsaw chain has been able to fulfill its motive of driving away your confusion regarding this topic. I’d consider it an accomplishment if I’ve managed to help you in any way with the help of this article.

The contents of this piece are written simply so that you can understand it and I guarantee that you won’t fail your task if you follow all the steps mentioned here correctly.

Our Latest Blog Post:

Article Source: www.wikihow.com

About the Author MF

MF is a 24-year young Blogger. He Started High Quality Guides to provide unbiased reviews, tips, and advice in the form of Top 10 Lists and beyond.

Leave a Comment: